Thermold Has Been Making Aftermarket Magazines Since 1966
Thermold is one of those iconic manufacturers who has been producing aftermarket magazines for just over half a century. Thermold prides itself on the development and design of polymer aftermarket magazines. This particular magazine is designed to be compatible with the FN FAL Metric Pattern platforms chambered in .308 Winchester. The magazine is designed to hold 20 rounds and is constructed from a durable Zytel Nylon.Thermold Aftermarket Polymer Magazine (Black) Specifications and Features:
- Thermold FNFALM
- Aftermarket Polymer Magazine
- .308 Winchester
- 20 Rounds
- Zytel Nylon (Polymer)
- Black
- FN FAL Metric Pattern and Similar Pattern Clones
16 Ratings
Perfect match for my KelTec RFB.
These are the same mags that came with my RFB. The new ones are a bit stiff to insert and drop but I am sure that will work out as I use them.
November 5, 2017
Ordered these mags in the
Ordered these mags in the FAL metric pattern for a new RRA LAR-8. They will not fit until you file off the top rib. No problem, just a couple of swipes and they slide right in. A couple more swipes and they will fall free. Plan on cleaning them up all over with a small file and 400 grit wet or dry sandpaper. But at this price I can spend a few minutes filing down sharp edges. Load'em up and they will run.
October 13, 2016
I find this product excep
I find this product exceptional for my application. In my opinion it is truly the best magazine for the RFB. I can't wait for it to be back in stock.
June 17, 2014
Was hesitant after readin
Was hesitant after reading the 2010 reviews but got three for my new RRA LAR-8. They work great. File a little on the back catches. RRA made modifications. I am currently ordering more!
April 13, 2014
These fit just fine in my
These fit just fine in my Rock River LAR-8. No problems. Exact same magazine as supplied with the gun by Rock River Arms. Good quality mag for the price
February 27, 2014
Need a little dremel work
Need a little dremel work to work in freely on an L1A1. Then a little more to get to drop freely from the weapon. Would have given more bullets if they worked without my help. Not much material had to be removed, just remove a little each time untill its moving in and out freely
December 6, 2013
The pic is wrong, the met
The pic is wrong, the metric only has the single lower rib. Got this for my RRA LAR-8. They are the same polymer mags that Rock River Arms sells, sans the RRA stamp. They have proven far more reliable than the steel FAL mags (which tend to have double feed issues in RRA LAR-8s). Had to do some slight modification to get it to drop free. These are all I use for my .308 (have 4, may buy more).
April 27, 2012
Not Magpul quality .... b
Not Magpul quality .... but feeds my RFB perfect, no modifications needed.
April 6, 2012
I bought these for my Roc
I bought these for my Rock River Arms LAR-8. They are much lighter than the metal mags, load easier, fits tight in the mag well with no rattling or looseness and eject with a touch of the mag release button. Required no dremelling, or anything else. The good thing about the LAR-8 is it will take inch and metric mags interchangeably. I will use these mags exclusively for a while, and give further review on longevity.
December 10, 2011
Buy the metric FN/FAL The
Buy the metric FN/FAL Thermold Mag for your Rock River LAR-8. The picture is incorrect, the metric one is missing the extra ribs. The Metric fits my Rock River LAR-8 .308 just fine, no dremmeling. Don't buy the inch pattern. I gave it 4 bullets because it could use a self leveling follower. Other than that a good product for the money.
September 11, 2011
Works like a dream in RRA
Works like a dream in RRA LAR-8 if you dremel off the upper rib.
July 6, 2011
I was pleasantly surprise
I was pleasantly surprised when I tried this mag in my RFB. Initial fit was too tight but after removing a minor amount of material it functioned flawlessly. Will be purchasing more.
March 30, 2011
Fits perfectly in my L1A1
Fits perfectly in my L1A1 upper. Nice tight fit with no wiggle or rattle. I won't get a chance to shoot for a few days but it cycles rounds manually just fine.
January 12, 2011
I got two of these magazi
I got two of these magazines yesterday and they don't even fit in a true FAL. That's pretty bad if it doesn't fit in the gun it is designed for. The raised lip doesn't allow the bolt to go all the way forward when the bolt is open, and when its closed the magazine won't even insert all the way. These magazines are nice and solid, but it doesn't matter if they don't work.
December 24, 2010
Yep. Does not fit the Ro
Yep. Does not fit the Rock River Arms LAR-8 at all! The first rib from the top is way too wide to go into the lower assembly. Returning via RMA. These are high quality, however only purchase if you have a FN-FAL. 2 stars off for the weak description and CTD didn't bother to inform me that they were out of the metric pattern until AFTER my huge order shipped!
December 3, 2010
These do not fit the Rock
These do not fit the Rock River Arms LAR-8 due to the highest raised rib around the magazine. Other than the 3 raised ribs, this magazine is the same size as my metal FN/FAL mags.
December 1, 2010
Will this work for a r1a1 sporter?
Answer:
Yes it will.
Will this work on a fnar chambered in 308 ?
Answer:
No. The FNAR uses it's own specific proprietary magazine.
Do these magazines work in the Keltec RFB?
Answer:
Yes, they do.
Do these allow for the last shot BHO on applicable rifles?
Answer:
Yes they do.
How well do these magazines work with a DSArms SA58
Answer:
They work well.
Does this magazine fit a Rock River lar-8 308 Caliber
Answer:
Yes. Rock River LR-308 uses FAL pattern mags.