Tired of bulky holsters with annoying clips or stubborn loops that require a belt just to carry your firearm? The people at Sticky Holsters were too, so they decided to do something about it. The result is a slim, low profile holster that provides comfort and peace of mind to all those that wear it.
The exterior is made from a non-slip material that sticks to nearly anything with just a little pressure; thus eliminating the need for clips or loops. The inner portion of the holster is constructed of closed-cell foam that keeps your pistol secure. Pressure and consistent use conforms the holster to your firearm, which means it only gets better over time. These lightweight holsters weigh next to nothing and allow you to draw your firearm in seconds. Throw that bucket of old, unused holsters in the trash and pick up the last one you'll ever need.
Specifications and Features
MD-1 Sticky Holster
Ambidextrous
"Sticky" outer material eliminates the need for belt loops or clips
Holster is formed by pressure and body heat from normal use
Closed-foam interior keeps lint and dust out
Black
Fits:
Accu-Tek AT-380 II/HC-380
AMT Backup
Glock 42
Kel-Tecl P-11/P40/PF9
Ruger LC9
Sig P290/P938
Taurus 709/708/740
Cobra Patriot
Kahr PM40/PM9/CM9
Kimber Solo
Bond Arms Snake Slayer
S&W Sigma 380
DISCLAIMER: "Glock" is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. and Glock Ges.m.b.H. Neither Cheaper Than Dirt!, nor this site are affiliated in any manner with, or otherwise endorsed by, Glock, Inc. or Glock Ges.m.b.H. The use of "Glock" on this page is merely to advertise the sale of Glock pistols, parts, or components. Components and parts that do not specifically have Glock listed as the manufacturer are made by their respective company. Such parts may be intended for use with Glock components but are not produced by Glock, Inc.. For additional genuine Glock, Inc. and Glock Ges.m.b.H products and parts visit www.glock.com.
The exterior is made from a non-slip material that sticks to nearly anything with just a little pressure; thus eliminating the need for clips or loops. The inner portion of the holster is constructed of closed-cell foam that keeps your pistol secure. Pressure and consistent use conforms the holster to your firearm, which means it only gets better over time. These lightweight holsters weigh next to nothing and allow you to draw your firearm in seconds. Throw that bucket of old, unused holsters in the trash and pick up the last one you'll ever need.
Specifications and Features
MD-1 Sticky Holster
Ambidextrous
"Sticky" outer material eliminates the need for belt loops or clips
Holster is formed by pressure and body heat from normal use
Closed-foam interior keeps lint and dust out
Black
Fits:
Accu-Tek AT-380 II/HC-380
AMT Backup
Glock 42
Kel-Tecl P-11/P40/PF9
Ruger LC9
Sig P290/P938
Taurus 709/708/740
Cobra Patriot
Kahr PM40/PM9/CM9
Kimber Solo
Bond Arms Snake Slayer
S&W Sigma 380
DISCLAIMER: "Glock" is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. and Glock Ges.m.b.H. Neither Cheaper Than Dirt!, nor this site are affiliated in any manner with, or otherwise endorsed by, Glock, Inc. or Glock Ges.m.b.H. The use of "Glock" on this page is merely to advertise the sale of Glock pistols, parts, or components. Components and parts that do not specifically have Glock listed as the manufacturer are made by their respective company. Such parts may be intended for use with Glock components but are not produced by Glock, Inc.. For additional genuine Glock, Inc. and Glock Ges.m.b.H products and parts visit www.glock.com.
Good starter holster.
I carry my Ruger .357 snub in this holster. It works. Not the greatest but it works. For the cost it good.
April 25, 2019
Will this fit a Ruger EC9S?
Answer:
Yes this should fit.