ProMag 10 round 9mm luger magazine replacement for your M&P-9. Extra magazines are always a good idea, and you should never be without some spares. These M&P-9 magazines hold 10 rounds of 9mm luger, with witness holes, are made of steel, and have a blued finish.
Features and Specifications:
Manufacturer Number: SMI 23
ProMag S&W M&P9 Magazine
Caliber: 9mm Luger
Capacity: 10 Rounds
Body Material: Steel
Spring Material: Steel
Follower Material: Polymer
Baseplate Material: Polymer
Finish: Blued
Fits:
S&W M&P9
Features and Specifications:
Manufacturer Number: SMI 23
ProMag S&W M&P9 Magazine
Caliber: 9mm Luger
Capacity: 10 Rounds
Body Material: Steel
Spring Material: Steel
Follower Material: Polymer
Baseplate Material: Polymer
Finish: Blued
Fits:
S&W M&P9
I would buy this product again
These are the best option for running your m&p in california. They run brass, aluminum and steel casings flawlessly. Couldn't be happier.
April 29, 2018
no problems after multipl
no problems after multiple uses
October 4, 2016
I recently purchased 3 of
I recently purchased 3 of these for my m&p. I had nothing but issues as soon as I started using these. Failure to feed issues, the follower would jam and rounds would turn freely and the last round will not extract. I had the same issues with all 3 mags I purchased. I compared them to factory ago at the range and I had not one issue with the factory mags. These mags re poorly made. The price point seems like a sweet deal but it's not. Your just giving your money away. Just go with factory magazines.
January 21, 2016
I bought 3 of these and I
I bought 3 of these and I've only put a couple dozen rounds through each one, after dry running them in & out of the gun multiple times. They are not as good of quality as S&W mags, but they are less than half the cost. You can tell they are light and made of a thinner metal. They don't fully eject the way factory ones do, so you have to pull them out when reloading. This is probably due to the lighter weight.The first few times putting them in the gun, they didn't click in immediately and I had to apply a good amount of pressure for them to fully engage. After multiple dry runs in and out, they clicked in much better so they just need to be broken in a bit.As for feeding, I have not had any feeding issues and they seem to feed reliably.Overall, worthwhile as SPARE mags because of the price, as long as you make a practice of pulling the mag out and not relying on it to fall out the way the factory ones do.
June 24, 2014
I ordered two of these be
I ordered two of these because no other magazines were available from any other manufactures. I should have realized that these were available for a reason... that being that no one wanted them because of the poor quality. Both of the magazine fail to feed without multiple jams and both fail to lock the slide open on last round. Don't waste your money on these. My factory Smith and Wesson M&P magazines work perfectly so I know it's not the handgun there are being used in.
June 2, 2014
will this mag fit the new 9mm S&W FPC carbine ?
Answer:
It should.
Are you able to disassemble the mag and base plate to clean?
Answer:
Yes you can.
Will this fit m&p 2.0 compact ?
Answer:
Yes it will, but it may extend out of the magwell past the grip.
Will this fit a S&w response?
Answer:
If you have the factory original setup, then this will fit. However, if you have switched to a Glock mag well adapter, then this will not fit.
I live in a 10 rd state and have the M&P 9 pro with the 5 inch barrel, will this magazine fit this handgun?
Answer:
Yes this will fit.
I live in a 10 round state and was wondering if this will work with a M&P 2.0 full size that came with 17 round magazines?
Answer:
Yes it will.