The Firefield Carbine AK-47 Quad Rail is a precision-machined hard anodized aluminum Picatinny rail that is a great choice if you're looking to replace your AK-47's standard wooden handguards. With six inches of rail space on each side, you can easily mount a variety of optics and accessories including lights, lasers, vertical forward grips and red dot sights or scout style scopes. The rail installs on your rifle easily with little to no gunsmithing required.
Features and Specifications:
Manufacturer Number:FF34008
Carbine Quad Rail
Material: Hard Anodized Aluminum Construction
Dimensions: 8.65"L
Weight: 8.8 oz
Includes MIL-SPEC Picatinny Rails
Numbered Rail Slots
Black
Fits: SAR-1, WASR, Norinco, MAK-90, US Arsenal, and Bulgarian AK Rifles
Features and Specifications:
Manufacturer Number:FF34008
Carbine Quad Rail
Material: Hard Anodized Aluminum Construction
Dimensions: 8.65"L
Weight: 8.8 oz
Includes MIL-SPEC Picatinny Rails
Numbered Rail Slots
Black
Fits: SAR-1, WASR, Norinco, MAK-90, US Arsenal, and Bulgarian AK Rifles
54 Ratings
If looking to place on a wasr stay far away
If you're looking to place on a wasr dont bother with this it isnt worth the headache, spend the money on a better unit go midwest
January 10, 2021
for VSKA
Had to remove material to fit on VSKA.I
November 13, 2020
Took a lot of work to mount on VSKA
Had to grind 2mm off each side of top rail for my gas block to fit. I have a VSKA. Looks good once its on but Took quite a bit of work, so if you have a VSKA be prepared to work.
June 16, 2020
Yes
Fit very snug on my c39 V2. Feel comfortable mounting Scout scope and keeping zero. Had to do a little massaging with a file, but that was to be expected.
June 4, 2020
TIGHT
Fit REALLY snug on my AK. Be very careful when tightening down the top part over the gas tube as it may crack if tightened too much. I expected a little fitment to be required. And had to perform just a touch of filing here and there. Use it for scout scope and I'm satisfied with zero keeping ability. Pros: Solid mounting
June 4, 2020
Lots of milling, or dremel required for wasr 10.
Not Sure of other models, but wasr10 did require a LOT of milling to fit over the beveled edge of the gas tube. I do recommend trying a different models if you plan to use this on the wasr 10.
January 9, 2019
Not even close
PSKak47... This product does not come close to fitment. The top piece is way to small to fit over gas tube the lower is to long...
January 2, 2019
Garbage
Doesn't fit my Century Arms AK at all. Requires material to be shaved off of different points, not practical for someone who is not a gun smith or someone that doesn't have the professional tools to properly shave down. Going to be a loss of money due to damage received in attempt to install which did not happen. Cons: Useless
May 17, 2018
I would not buy again !
First it didn't even come close to fitting my Mak 90, so I started with a Dremel and files and finally an end mill to hog out the inside enough to fit over the gas tube, I went very slow and tested it's fit allot to make sure I didn't remove to much and after 5hrs. of working on it it fits perfectly.... I wanted it to mount a Mako forward grip/bipod and it works great now, but I recommend buying a different brand or better quality.... it might fit your variant just fine but it didn't fit mine. (it is well made and strong)
May 2, 2018
Fit wasr 10 just fine
Very well built, fit my wasr 10 with a little persuasive use of a rubber mallot, but overall no grinding or anything was necessary and made quite the difference in adding accessories and helped the look. Pros: Well Built / Quality Cons: Slight agressive asembly
March 24, 2018
Great quality, poor fit
Getting the top rail section to fit over the gas tube is a nightmare for a WASR-10. Be prepared for a lot of grinding. A LOT.
March 3, 2018
Not terrible but not great
Overall not a bad handguard. Few cons, I had to force it onto my wasr 10. The screw heads do strip out easily if you overtighten which is extremely easy to do and you'll notice when you go to charge the rifle and you feel some stickage from the excess pressure pulling down on the gas tube. But I have over 600 rounds through the hand guard. It gets hot fast so rail covers recommended. I don't regret buying this product. I just wouldn't buy it again knowing what I know now about it
February 22, 2018
Does not fit I.O. Inc. AKM
This piece seems to have a solid construction, but the top part is too narrow to fit over the gas tube of an IO, inc. Sporter. I had to return it.
February 5, 2018
Love it!
I installed this in about 10 minutes on my Century Arms AK47 and it looks... omg. It just looks so mean. It did take some force to get it on but once it got on it was there and it's not going anywhere. Very sturdy construction and really easy to figure out. Love it!
June 27, 2017
I would have given this 1
I would have given this 10 stars due to the high quality construction , but the amount of filing and fitting to get it to work with my RAS47 made it a difficult install. The bottom rail assembly required 1/8 of an inch of material to be dremelled out. No biggie there. the top part that goes over the gas tube required an substantial amount of material to be removed in order for the rail to fit over the bulge of the RAS47 gas tube.Do not overtightened the top rail too much or piston is restricted
March 12, 2017
Very well made and priced
Very well made and priced railed handguard. It is tough thick and a little heavy. I put it on a ras47 and it locked on good and tight with no modifications or filing needed the bottom is slightly shorter than the wood guard but has posed no problem with fit or function.
January 19, 2017
Awesome rail system. It m
Awesome rail system. It may not list AKM as compatible but it fit my RAS just fine only slighly shorter than the original wood handguard, which is still plenty of room. Only took about 10 min to install only an allen wrench was needed. Keeps the heat off your hand very well too all in all for the price awesome rail.
October 23, 2016
bought this for my i.o in
bought this for my i.o inc akm247c (ak-47) tight fit had to tap in place fit perfect...
July 10, 2016
Fits quite well consideri
Fits quite well considering the price. The instructions it came with were for an AR style weapon so they were useless. Just kind of had to try and guess how it worked together. Still tight 300 rounds later. The heat really soaks right through so using gloves or maybe getting some covers would be required. I'm using a foregrip and it seems to be working quite well.
March 4, 2016
Fits my I.O. sporter perf
Fits my I.O. sporter perfect! Now I mount my laser dot on the bottom and it does not block my regular sights. I have seen other rail systems go for more than 100 dollars glad i found this one.If you have an IO and plan to use this you have to buy a new gas tube IO gas tube and upper can not be separated.
February 14, 2016
Very well made but too pr
Very well made but too precise to work on WASR. No matter my Dremel use, could not make fit.
June 15, 2014
I bought this forearm, th
I bought this forearm, thinking it would bolt right in. That is not the case, unfortunately. On a MAK 90, I needed to file about 1/16 inch or more of the aluminum from the bottom half of the handguard from the end that sits against the receiver. Then, I needed to file metal from the lower half at the forward end of the forearm, so when the gas tube was installed, the forward retainer for the wood handguard would not catch on the lower handguard. It took a while to figure out how to proceed, but once it was on, it fit really solid and looked great. Now I just have to figure the best way to refinish the aluminum where the metal was removed.
December 1, 2012
I have a Norinco Mak-90 S
I have a Norinco Mak-90 Sporter and the top rail fits snug. The only problem is the lower rail needed 1/4in. dremmeled to fit snug. The results are satifying after all said & done. The issue with not having directions in is not an issue.
September 11, 2012
I bought this a couple of
I bought this a couple of months ago for my Arsenal SGL-21. After getting the original factory foregrip off, I then went to install this. Fit like a dream, no machining, nothing, just had to play with the bolt to make it level because of the design. I rate this a 4, simply because I figured it would dissipate the heat a little better than it does. Other than that, it is a great product and a hell of a lot cheaper than buying something similar at my local gun store (they wanted $114 for something similar). Got my red dot and vertical foregrip on it now. 7 months in, still solid. P.S. just don't over tighten the Allen headed bolts; they have a tendency to start stripping if you tighten them too hard. ;)
August 3, 2012
Two bullets, as the craft
Two bullets, as the craftsmanship of the item is quite good. However, the website itself is misleading. This does not, repeat DOES NOT, fit my Norinco AK-47 (type 56s-1). The bottom rail is about 1/4 inch too long for the bottom handguard lock to completely lock. The top rail fits the gas tube quite snug, so there were no issues there. Again, this item will NOT fit on my Norinco AK-47 rifle. Returned the item today, and will be trying the UTG rail next.
June 3, 2012
Pros: looks cool, can add
Pros: looks cool, can add stuff on it. Cons: doesn't fit Kbk wz. 1988 Tantal AK-74s. It really messed up my piston chamber. Hey, maybe it fits most AKs and I just didn't get lucky! But I'm giving it 3 bullets.
February 20, 2012
I only gave this product
I only gave this product 1 bullet because 0 was not a choice. It did not even come close to fitting my AK, and I damaged both just attempting to get it off! Spend the extra $$ and get the UTG. Cheaper Than Dirt should not even carry this horrible, horrible product. Firefield knows full well it's terrible. They cover themselves in every way possible from any liability, because I suspect I am not the only customer with this or similar complaints. OK, rant over, but save yourself my frustration and DO NOT buy this product!
February 7, 2012
Well, like everyone else
Well, like everyone else said this doesn't come with directions. But if you know AK's and are decent with tools you'll figure it out. It took me about a half hour to put this on. Had to tap the top piece in with a rubber mallot. Holds firm to my WASR-10 and I didn't have any issue getting it level. Attached a Vortex Spark to it and zero'd it in about 10 shots. So far I've been able to hit consistanly at 150 yrds plus. Not bad for what you spend.
January 8, 2012
I am not too happy with t
I am not too happy with this product. talk about a lot of work, I had to trim some off to get it on my AK 74. another thing is it lined crooked as hell. its a good thing I am only using it for a grip and flashlight because a scope would never work. for what i need it for its just fine but I would spend the extra money on a different one.
December 28, 2011
If you know anything abou
If you know anything about AKs or tools, this quad rail is easy to install and holds tight to the weapon. I really like the look of my AK with it installed. Even my wife thinks it looks alot different. CTD was amazing as usual with their shipping and customer service.
December 19, 2011
Very sturdy setup. I bou
Very sturdy setup. I bought a Tapco Intrafuse vertical grip with this. Very pleased! If you know your gun decently, it's not much of a problem to install without instructions.For the WASR 10-63: I had to put both the top and bottom rail in place LOOSELY in order for the sling-mount to properly secure. Keep the top rail (w/gas port) as loose as possible, but as near a uFFFDseateduFFFD position as possible, b/c you'll need some space in order to push the tab on the sling-mount backwards. If you don't leave some room, then the metal tab on the sling-mount will hit the gas tube and won't be locked.Once you have the sling-mount and bottom rail secured, then you can install the top rail. I had to flare out the corners of the gas-tube mount (with pliers) where it butts up next to the top/bottom rail. You'll see what I'm talking about when you get to it. The new rail system was designed for the top rail to go straight down onto the bottom rail, but the gas port (which has the top rail on it) actually goes down at an angle; flaring out the corners slightly will allow the top rail to fit onto the bottom rail. Hope this helps some of you.Keep in mind this might not work on all AK's and other tricks might need to be used instead.
November 13, 2011
It's a great product and
It's a great product and would recommend it to anyone. It does how ever come without directions but if u know your guns and have tools u can install it in about 20 minutes or so. And besides it looks cool.
November 7, 2011
First off this thing come
First off this thing comes with no directions so good luck... After that it's a good looking addition to any AK, BUT it took a butt load of work to get it to fit my WASR-10. It was very tight going on and getting the screw holes to line up was a challenge to say the least, but when all was said and done I'm happy with it, so just be ready to do a little work.
September 16, 2011
Just installed this on my
Just installed this on my AK-47 WASR-10 Romanian and I LOVE IT! You might need a flat head screw driver and a rubber mallet. This baby is SWEET though! Took about 15 mins to get it on. Can't beat the price either!
July 27, 2011
The forearm and delivery
The forearm and delivery deserve the 5 bullets. My personal experience gets 2 bullets. Initially the forearm went on w/o a hitch. Just a few 'love' taps with a mallet and it was tight. Then I noticed the handguard lever on the lower portion of my AK was in the forward position. Took it apart put the lever back and then nothing fit. Did some dremel work, malleting, cursing, and lost some flesh on the handguard. Ended up leaving the lever forward and it went together fine. Great product irritating w/o instructions. Youtube helped.
July 18, 2011
Looked to be a quality pr
Looked to be a quality product made very well. Upon installation however, things went downhill. No instructions!! The lower foregrip was the main source of trouble. I mounted it to a standard MAK-90. The lower foregrip merely butts up to the front of the receiver..nothing ties it into the well of the receiver as with the stock wood furniture. Same problem with front of the lower quad rail. The front retaining bracket that cams into the barrel merely fits flush with the rail..but does not tie into it. It depends on the upper gas tube for rigidity. Considering the torque forces placed upon the quad rail with a vertical foregrip, there's plenty of rome for movement. THIS IS NOT A 'NO GUNSMITHING' MOUNT! Overall..pretty disappointed in it.
July 18, 2011
This would have easily be
This would have easily been a 5 if it had not been for the fact that there are no instructions provided. I had to surf Youtube and figure it out by looking at similar items from different manufacturers. End result, Perfect Fit. Rock Solid. Hi quality. Will be interesting to see how hot it gets :)
July 15, 2011
I was skeptical at first
I was skeptical at first due to all the previous reviews. I didnt need to dremmel or file anything down for my WASR-10. I didnt even need a rubber mallet. I just used Vice grip wrenches to synch down a perfect fit. (use a sock or cloth to prevent the wrenches from scratching the finish) After I synched it down, I used the screws to hold the guards in place, and cycled through until the whole unit was installed. Its a sure fit, with no vibration. Mounted an EO Tech and forward grip with-in 20mins. Lock n load!!!
July 6, 2011
reviews say it would fit
reviews say it would fit my model ... checked over and over... so finally i orderd it... n IT DONT FIT ofcourse! in no way would it ever without major modification... SUCKS!!! really dissapointed... ! REALLY dissapointed... ! dont wast your time or money!!!
July 1, 2011
No doubt it took 30 minut
No doubt it took 30 minutes of filing to get it to fit my mak-90, but the end result was tight with no wobble. Not bad.
July 1, 2011
I gave it 3 bullets only
I gave it 3 bullets only because I had to modify it to make it fit my WASR-10. Needed a little (a lot) of TLC with a dremmel to fit over the collar on the gas tube... once it was clear, it fit sung and looks awesome! Im very happy with the final product.
June 28, 2011
Hold just as well as any
Hold just as well as any of the $70+ quads, even for optics.If I ever own a second AK-47, this will be my first buy.
May 22, 2011
i installed this on my ma
i installed this on my mak-90 without a problem. It fit very snug and no part is loose or wobbles. Very happy with this product!!!
March 31, 2011
Took a total of 30 minute
Took a total of 30 minutes worth of filing it down to make it fit my WASR 10. No instructions.
March 30, 2011
WOW,took some time to get
WOW,took some time to get the wood grips off but when I did it fit just fine....and it looks wicked nice 5 bullets all the way thanks CTD!!!!
March 29, 2011
I just got it in the mail
I just got it in the mail and installed last night. It looks great on my AK. However; I do not know if this quad rail is 922r compliant or not becuse this quad rail is made in China. Now I am concerned :(
March 29, 2011
I installed this to my Hu
I installed this to my Hungarian 85M. It fits great and I installed a red dot sight and a UTG light and front grip combo. I have fired 200 rounds with no problems. It did not come with instructions, look to you tube, and no plastic covers. It is very light weight and sturdy. I will try another one on my Romanian SAR2.
March 20, 2011
I was very weary about ch
I was very weary about changing out the wood on my AK but I wanted to be able to shoot my rifle with comfort because my MAK-90 was made for right handed and I shoot lefty. So this was the best decision I have ever made. The quad rail fit absolutely perfectly. I couldn't be any happier! Thank you Cheaper Than Dirt. By the way fed ex sucks.
March 6, 2011
This guard took me all of
This guard took me all of 5 minutes to install....looks awesome, if you put a foregrip handle on it you won't have to worry about how warm it gets when you rapidfire rounds through it...i would recommend it to anyone who owns a wasr 10
February 26, 2011
When i got this in the ma
When i got this in the mail i did not think it was going to fit it does not attach like your wooden ak grips the retainer clips that hold on to your wooden grips are not used to hold this on you have to put the bottom piece and the top piece on the gun together and screw it together tightly. You may need to shim in order not to put too much pressure on your blow back tube but once you get it on it holds together nicely, the down side is that it gets extremely hot!!!!! if you put 60 rounds at some what a rapid rate you have to put the gun down for at least thirty mins, if you get this you will need rail covers i just ordered mine last night.
February 18, 2011
Got it in two days. Great
Got it in two days. Great job as always CTD. As with everything I've done on my AK, the hardest part was getting the originals off. The bottom portion of the handguard went on flawlessly and locked in very securely. The top handguard was a bit more tricky and required minimal filing with a hand file, more than easy and gives the handguard a custom fit that was worth the 10 minutes of extra work. Holds securely everything I have attached and cost less than the others out there for the same quality. Lighter than the others, too. I have a chinese barrel and heard it would be trickier than others but overall pretty painless.
February 1, 2011
At first I wasn't sure if
At first I wasn't sure if this rail would fit my AK-47 (made by: Armory USA.). After ordering and receiving it in the mail, I removed the stock-wood forend (and pistol grip) and installed the rail. The rail fit perfectly! I added this rail along with a few other accessories, and the AK looks a lot more modernized (like a completley different gun), and it is also a lot more functional. The quad rail has a red dot sight on it, and some magpul 'ladder' rail covers. I also put a Tapco SAW pistol grip on it, and a Blackhawk M4/AR-15 buttstock mag pouch holder on top of the underfolder stock, which isn't really meant for this setup, but I made it work for me. (I have a 20-round AK mag in the pouch, a 30 rnd mag doesn't really fit since it's made for a 30 rd M4/AR mag.). The AK-47 looks like an entirely different gun from the original plain/wood grips, and I absolutely love it!
January 22, 2011
Great rail system. ROCK S
Great rail system. ROCK SOLID for optics. No need to buy the more expensive ones.
January 22, 2011
This rail system fits rea
This rail system fits really well. I put 180 rounds through my WASR 10 and it held zero perfectly with my scope. The barrel heat doesn't get through to your hands. I think its a great rail system for the price.
October 25, 2010
Will this fit a Hungarian Ak AMD 63?
Answer:
Yes, it should fit. Some fitting may be required.
Will this fit the Zastava ZPAPM70
Answer:
No it will not
Will this fit a pioneer Hell Pup Ak47 pistol??
Answer:
Yes it will.
Will this fit my century arms darco
Answer:
It should fit the full size Draco model, minor fitting may be required
Will this fit century arms micro Draco ak
Answer:
Not the micro model, no
Will this fit Egyptian Mardi AK 47?
Answer:
Yes
Will this fit a C93V2v
Answer:
Yes it should fit.
Will this fit the Riley Defense RAK-47 P!"?
Answer:
Yes it should, fitting may be required
Will this fit pioneer arms sporter ak-47?
Answer:
Yes it will, minor fitting may be required
Will it fit the rak47 by riley defense
Answer:
Yes it will. Minor fitting may be required.
Will this fit on a m92 pap pistol
Answer:
No it will not.
Will this work on a Nak9
Answer:
Not that we are aware of.
Will this fit an Arsenal SA-93 that is from the early 90's out of Bulgaria with the wooden thumb hole stock?
Answer:
Yes
Will this fit on a century arms vska?
Answer:
Yes
Will this fit a Arsenal SAM7K-44 pistol AK47?
Answer:
Yes it will.
Can this be used with a Century Arms Draco AK pistol?
Answer:
Yes
Will this work for MDL M70 zastava Ak47
Answer:
No it will not. Item AKS-276-002 will fit.
Looking for the best one of these for my hellpup. Also the best way to mount a folding stock
Answer:
This should fit the Hellpup. You cannot legally put a stock on a Hellpup, but checkout item AKS-17-073
Will this fit a PSAK-47 GF3?
Answer:
Yes, it should.
Will this fit a century arms mini draco?
Answer:
No it will not.
Will this fit a C39V2 rifle?
Answer:
Yes it will.
Will this fit a Saiga M3 EXP ?
Answer:
Yes, it will.
Will it work with an underfolder type stock?
Answer:
Yes it will.
Will this fit pap m79
Answer:
No it will not.
Will this fit a ras47?
Answer:
Yes, it will.
Will this properly fit my IO ak47 c
Answer:
Yes.
Will it fit CIA RI2085 PAP RIFLE 762X39 SYN
Answer:
No it will not. Item AKS-631-002 or AKS-276-002 shoudl fit.
Will this fit century arms draco?
Answer:
Yes.
will it fit a wasr 10??
Answer:
Yes it will.
does this come in earth color?
Answer:
Unfortunately the Firefield AK-47 Carbine Quad Rail does not come in earth color.
Will this fit a zastava N-pap?
Answer:
No it will not.
Will this fit an arsenal Sam 7?
Answer:
Yes it will.
Will it fit the IO inc AKM247?
Answer:
Yes it will fit your IO AK-47.
If this product does not fit, can it be returned?
Answer:
The item is returnable. You can read our full return policy from the link at the bottom of the page.
Will it fit a ras 47?
Answer:
Yes it will.
What color is it ... is it heavy duty ?
Answer:
The description has been corrected. The color of this item is black.