The Barska AR-15 Carry Handle doubles as a rear sight system.
This 2-in-1 one detachable carry handle and rear sight fit on flat-top AR-type rifles. The integrated rear sight allows for windage and elevation adjustment. Two strong locking thumb nuts keep the handle secured in place whether carrying or firing.Barska AR-15 Carry Handle Features and Specifications:
Material: AluminumLength: 7"
Finish: Matte Black
Fits: Picatinny/Weaver rails
13 Ratings
Loose on rail
Fits loosely on my S&W M&P15
September 14, 2021
i would buy again
got this for my windham src 308 went on with no problems fits secure looks good
February 23, 2018
Cheap
It wouldn't clamp onto the rear of my flat top rail I had to disassemble it and as another mentioned it striped off some of the threads in the nuts, I could tell it was stake on the bolts so I put some oil on to remove the nuts. I noticed the front stud was bent down so I matched the rear by bending it down but had to open up the rear hole in the clamping plate with a pencil die grinder to get it to make contact with the rear of the rail. I also ground a chamfer to remove the stake marks on the ends of the studs on a bench grinder before putting the nuts back on. To much wrong with it better to spend a little more and get one that bolts right up with no custom modifications. My sons friend had the same problem....
January 3, 2018
The rail clamp didn't eve
The rail clamp didn't even make contact with sides of my upper when fully tightened. I can fix most of what stupid does, but I can't fix stupid. I took off the cupped steel piece and cupped it further on the anvil, but surprise!, they staked the ends of the threaded studs so now my finger nuts are stripped. I filed off the staking burr and got everything tight, but with only about 15%thread engagement. It gets one star because the casting is ok I guess. Barska is junk, save up for a better one.
June 13, 2016
Ghost ring site on my SAR
Ghost ring site on my SAR ARMS autoloader broke and I couldn't get a replacement so I ordered this and slapped it on. Not only does this have a ghost ring site in it but now my tactical 12 gauge has a cool carrying handle!Fit was perfect and only one click site adjustment was needed.
March 29, 2016
For 27 bucks its just enn
For 27 bucks its just ennnnnh. My bad.
November 22, 2014
Very pleased with this ca
Very pleased with this carrying handle. Easy to install and only took a few rounds to sight it in.
April 13, 2014
Very pleased with this ca
Very pleased with this carrying handle. Easy to install and only took a few rounds to sight it in.
April 13, 2014
Easy to install and good
Easy to install and good quality.
April 5, 2014
Very easy to put on. Took
Very easy to put on. Took just a couple of rounds to get it sighted in. Good product for the price!
February 9, 2014
For the price it is as I
For the price it is as I expected. The reason I gave it a 4 is you can clearly see many machining marks on the side of the handle. And there are no notches on the flip piece of the sight to reference the windage marking on the base. However it will do its intended job and holds a zero fine.
January 16, 2014
Easy installation, just a
Easy installation, just a couple clicks to get in the red 28 of 30 shots !
October 12, 2013
Easy installation, just a
Easy installation, just a couple clicks to get in the red 28 of 30 shots !
October 12, 2013
I'm sure this will attach to any flat top receiver but is it compatible with "F" marked front sight bases?
Answer:
Yes. AR-15 front sights are a standardized height. This carry handle will work with any of them.
compatable with a Bear Creek Arsnal AR15?
Answer:
Yes. It will fit any AR with a Picatinny rail on the upper receiver.