Aimtech Mossberg 500/590/Maverick 88 12 Gauge Mount Black [FC-035724001033]

Aimtech Mossberg 500/590/Maverick 88 12 Gauge Mount Black [FC-035724001033]

nan ASM-3

Out of stock

nan ASM-3

Model
ASM-3
UPC Barcode
035724001033
Aimtech mounts are some of the simpliest to install and do not require gunsmithing; installed in three minutes. Does not interfere with Iron sights as they remain functional. Extruded and machined high strength aluminum alloy. Mounts scopes, electronic sights and lasers using Weaver-style bases. Weighs only four ounces. Installation tool and instructions included.

Features and Specifications:
Manufacturer Number: ASM-30
Fits Mossberg 500, 5990 and Maverick 88 12 gauge shotguns
Saddle-style mount
Slides down receiver and straddles both sides
No gunsmithing required
Quick target acquisition
Standard dovetail mounting rail
Accommodates Weaver/Picatinny rings and electronic sights
MIL-SPEC Type II anodized
Installs quickly
Non-glare satin black
18 Ratings
5 out of 5 stars
18 Ratings

Rated 5 stars by 100% of reviewers

Rated 4 stars by 0% of reviewers

Rated 3 stars by 0% of reviewers

Rated 2 stars by 0% of reviewers

Rated 1 star by 0% of reviewers

Rated 5 out of 5
Upgrade you shotgun
It comes with every thing you need to install it. If you’re using older eyes like me, the instructions are in really small print but there are YouTube videos you can watch. It was super easy to install. The rail is long enough to put a couple of accessories on there. This was a great inexpensive way to upgrade my shotguns.
April 16, 2022
Rated 5 out of 5
Good quality mount
Good quality product, mounts well on the Maverick and leaves a tidy sight well for factory beads as back up.Loses a star for1. Hardware could be better quality to match mount, stainless capped nut hanging off the receiver is tacky. Spend the time to engineer so either there is a steel thread into the mount on the forward or floating nut without protrusion internally.2. No liners on the mount, will certainly scratch the receiver if ever to remove it, 2 small strips of Teflon tape do the trick.
April 11, 2022
Rated 5 out of 5
Works as advertised & looks cool also. Cinch to install.
April 1, 2022
Rated 5 out of 5
Good product
Easy to install. Works as it should
November 26, 2021
Rated 5 out of 5
Looks good
Looks good
October 2, 2016
Rated 5 out of 5
easy to install comes wit
easy to install comes with all necessary parts along with instructions. makes for a quick and easy installation.
April 10, 2016
Rated 5 out of 5
works great ; easy to put
works great ; easy to put on ; great shipping
October 19, 2013
Rated 5 out of 5
Here's the truth. (Mossbe
Here's the truth. (Mossberg Maverick 88 user, here)Right out of the box, it looks great. Not a single problem with it. Longer than I expected it to be, which was a plus.Installation? What installation? You need a flat head screwdriver for ONE screw. The directions are over-complicated, regardless of how easy it is to discern them. Push out a pin, put the mount on, replace the pin with a screw without over tightening it, pump the forend back, unscrew that tiny screw in the ejector rail, replace with a slightly bigger screw (included), tighten the nut down that it also came with, and there you go. I know it was a waste of time to write that down here, but I figured it might help you decide that this is a good decision.It holds in place VERY firmly. Mine doesn't move, shake, or rattle whatsoever. The one and ONLY problem that someone might have with this is that is WILL scratch the shotgun underneath the mount. But you're putting a mount on it, which will hide any damage anyway... so... Who cares? Put a red dot sight on the rail with no problem. ALSO, even with the mount installed, you can see underneath it. Imagine it to be another sight for those with shorter barrels with only one bead.
July 5, 2012
Rated 5 out of 5
Here's the truth. (Mossbe
Here's the truth. (Mossberg Maverick 88 user, here)Right out of the box, it looks great. Not a single problem with it. Longer than I expected it to be, which was a plus.Installation? What installation? You need a flat head screwdriver for ONE screw. The directions are over-complicated, regardless of how easy it is to discern them. Push out a pin, put the mount on, replace the pin with a screw without over tightening it, pump the forend back, unscrew that tiny screw in the ejector rail, replace with a slightly bigger screw (included), tighten the nut down that it also came with, and there you go. I know it was a waste of time to write that down here, but I figured it might help you decide that this is a good decision.It holds in place VERY firmly. Mine doesn't move, shake, or rattle whatsoever. The one and ONLY problem that someone might have with this is that is WILL scratch the shotgun underneath the mount. But you're putting a mount on it, which will hide any damage anyway... so... Who cares? Put a red dot sight on the rail with no problem. ALSO, even with the mount installed, you can see underneath it. Imagine it to be another sight for those with shorter barrels with only one bead.
July 5, 2012
Rated 5 out of 5
Bought it for my maverick
Bought it for my maverick 88 to hunt with slugs this year. It went on quick and easy, I bore sighted the scope, and have put 80 slugs down range since with the scope holding 0. I even took the mount off without removing the scope from it and then reinstalled the mount to see how bad it threw it off and it might have been off by half an inch at 50 yards or it may have just been me. I wouldn't suggest any other scope mount for a mossberg shotgun especially since you can still peep under the scope to aim down the bead if you so choose.
December 2, 2011
Rated 5 out of 5
It works, plain and simpl
It works, plain and simple, it took about two minutes to install. Fast shipping from CTD, will buy more gear very soon....
October 19, 2011
Rated 5 out of 5
It works, plain and simpl
It works, plain and simple, it took about two minutes to install. Fast shipping from CTD, will buy more gear very soon....
October 19, 2011
Rated 5 out of 5
Looks great and fits grea
Looks great and fits great... Took no time to slap it on and tighten it up... My Mossberg just reached a whole new level of awesome....
March 31, 2011
Rated 5 out of 5
As stated by other review
As stated by other reviewers, this is an excellent bang for the buck! It says 3 minutes to install in the directions and that is no lie! This is very rigid once installed and contours the ejection port perfectly. All screws included AND made in the USA! CTDs done it again!
September 9, 2010
Rated 5 out of 5
This is just a great, gre
This is just a great, great accessory. The mount itself also provides a bit of a 'ghost ring' for the front bead, in that it draws your eye to the bead a little quicker. Loctite is required, #242 is recommended. Here's to hoping CTD gets it back in stock.
November 12, 2009
Rated 5 out of 5
This is just a great, gre
This is just a great, great accessory. The mount itself also provides a bit of a 'ghost ring' for the front bead, in that it draws your eye to the bead a little quicker. Loctite is required, #242 is recommended. Here's to hoping CTD gets it back in stock.
November 12, 2009
Rated 5 out of 5
Took about 5 mins to atta
Took about 5 mins to attach. Had to hand tighten screw from within the chamber. Liked the see-thru design. Attached a red dot with zero problems. Simple and effective product.
August 17, 2009
Rated 5 out of 5
I bought one of these for
I bought one of these for my Maverick 88. It attached flawlessly, everything fit perfectly. Came with all the hardware and tools needed to fit it. Nothing I can complain about. Great scope mount.
April 2, 2009
Will this fit 88 20 gauge?
Answer: No this will not fit.
Will it work on a mossberg 535
Answer: Yes
Will this work on a maverick 88 20ga?
Answer: No it will not
what are the dimensions?
Answer: It's a mil-std 1913 Picatinny rail.