Welcome to Cheaper Than Dirt! Shop 200,000+ deals on firearms, ammunition, gun parts, survival gear and more. All in stock and ready to ship.
| Next

Mag Cobray M11 9mm Blued 30 Rounds Steel Magazine

Multiple Manufacturers
Ships from Warehouse 1
Typically ships the same business day when ordered before 4pm CST.
We regret that this item is not available at this time.
Can we ship this to you?
Cobray M11 30 Round Magazine.
Steel magazine fits the M-11 auto pistol and SMG. M-11 9mm 30 Round. May hold more than 30 rounds.
Total number of Reviews: 9

Submit a review

4.0 5
"I ordered 5 magazines. These aren't the rare metal Cobray magazines but they funtioned perfectly. I was a little weary at first because they don't conform to the shape of the M11 magwell and seat a little crooked. Later I fired 300 rounds at the range without a problem. I'd buy more of these if I needed them."
1.0 5
"a rather bad fitting magazine. matched only by its (no)quality manufacturethe rear catch for the mag release is out of location on the mag I received, it holds the magazine almost 1/8 of an inch too high compared to the bolt face.works great as a bolt hold open device.there are also three spots on the mag body where it had dents that must have stuck out, now they're just paper thin with jagged holes where someone at the factory went nuts on the belt sander. they should have stuck to assembling flashlights and sewing wallets.I'm not even going to try to rework this thing, it's going on the junk pile."
1.0 5
"I ordered two of these and they would not fit my Cobray M-11 at all. I could get one or two rounds off and then the clip would either fall out or would not feed because of the misfit. Do not buy this magazine."
3.0 5
"When I got these mags I could not lock them into my M11/9. After hammering down and filing off the front catch they slid in easily and locked tight but with quite a bit of play. Much to my surprise both mags functioned perfectly, despite the rather loose fit. I don't like 'em near as much as Zytels or refurbished steels but I would recommend these as a source of cheap mags with the caveat that some minor fitting may be required. These would be a good choice for modification into a 50 rounder or as the feed tower on a suomi drum."
1.0 5
"I bought five of these mags, also. They will not work in my Mac 11. If your're lucky you might get one round off. A total waste of money!"
2.0 5
"Got 4 of these magazines, all 4 have an issue with the feed angle not being correct. Basically they need tweaking, one of four would not lock into gun properly without \"persuasion\" from a grinder, and all four needed the feed lips flexed inward to reduce feed angle. More work than what they are worth, until you look at the alternatives, which are huge $$$. Ok if you like to tinker, but avoid if your time is very valuable."
1.0 5
"I had high expectatins bc all my factory mags are plasitic and i was looking forward to a steel mag... Not the case here! This mag will not stay in place, it keeps falling out. Some MAJOR custom modifications are needed. Next time, I'll put out more money for another plastic one.... Not a good buy!!!"
4.0 5
"At first I was displeased with these magazines. Only one would even lock in my Cobray M-11/nine. After a little inspection I found the piece of steel welded along the backstrap was a little too long and prevented the mag from locking in. I measured the one that worked and ground down the others to those dimensions. I've since filled and shot empty all of these mags at least 3 times each. I had one failure to feed in a mag that later worked fine, otherwise no problems. These mags are a rough (particularly now with grind marks in the backs of them) but they're cheap, and after a little tweaking function fine for me. Factory steel M11 mags are very expensive. For a lot less money and a little work, I have metal mags that work. I'm happy with them."
4.0 5
"I ordered two of these mags to see if they would work out. They worked fine for me. I'm going to order some more since those two were fine at this price. I can't beat it."