3 Top “Stow-and-Go” AR-15s

Disassembled DRD AR-15 rifle

A takedown AR makes good sense for your Go Bag, since you don’t necessarily want to reveal what you are carrying in a knapsack or bag. Three takedown ARs I have intimate knowledge of include the Windham Weaponry Model RMCS-4, DRD CDR-15, and Ruger SR-556 Takedown.

Disassembled DRD AR-15 rifle
The DRD breaks down into 4 components.

The bottom line is this, the Windham Weaponry Model RMCS-4 has the smallest footprint when disassembled, the DRD CDR-15 offers ease of use, and the Ruger SR-556 Takedown is pure rugged simplicity. Expect good accuracy from all of these AR-15s and no zero shift to note.

When I first started to dig into takedown ARs, I had an obvious question. Isn’t an AR already considered a takedown rifle? Can’t you just disassemble the lower receiver from the upper receiver and tote the two pieces in a duffle bag? The answer is yes and no.

Sure the AR design is modular, and the receivers can be toted unassembled. However, a takedown AR significantly decreases the footprint of the rifle. That means components can be carried around in knapsacks and duffle bags that don’t look like a gun case.

Disassembled Ruger takedown AR-15
The Ruger retains the upper receiver when torn down to 4 components.

Some takedown methods are faster and simpler than others. If assembly time was a factor, the DRD at 10 seconds, and the Ruger at slightly more, are fast. The Windham was longer, but rest assured, you can tear these rifles down and build them back in less time than it takes to load a 30-round AR-15 magazine by hand.

Another advantage to takedown ARs is the ability to swap calibers. At worst a different BCG, compatible magazine well, and barrel is all it takes. The Windham rifles shines in this aspect since it can shoot four different calibers—5.56 NATO, .300 BLK, 7.62x39mm, and 9mm.

Here’s a look at how these rifles come together. To assemble the DRD, lock the bolt carrier group (BCG) rearward, and then remove the end cap from the barrel assembly. Next, insert the barrel and gas tube into their respective holes in the lower/upper receiver component. Finger-tight suffices for the amount of rounds you will most likely be carrying in case with the rifle.

Windham takedown AR-15 disassembled
The Windham breaks down into 4 compact components.

The barrel nut has the same cut-outs as buffer tubes so you can also use a castle wrench if you were going to run a high round count through the rifle. Next, pull the retaining pin and unlock the cam lock on the rail. Slide the handguard over the barrel. Align the notches, push the retaining pin back, and lock down the cam. Insert a magazine and you are ready to fire.

The Ruger breaks down into three key components: lower receiver assembly, upper receiver/handguard assembly, and barrel/piston system assembly. To takedown the Ruger the first step is to pull out the pivot and takedown pins and remove the BCG. Next, move the slider bar on the underside of the handguard toward the rear of the rifle. Then, twist or rotate the barrel assembly clockwise with the muzzle facing away from you, and pull the barrel free from the handguard. The rear of the barrel has lugs that mate with grooves in the upper receiver. This is very repeatable and secure. The upper and lower are then disassembled like a standard AR-15. What I liked about the Ruger was the fact that you do not have to align a gas tube. The Ruger barrel/piston system assembly is sturdy.

To takedown the Windham, a bail on the underside of the handguard is flipped allowing the retaining block to slide toward the muzzle revealing two barrel retaining arms. The barrel retaining arms are easily rotated 90 degrees outward to disengage from the barrel. The barrel/gas tube assembly is then pulled from the handguard. Like with the DRD, the gas tube of the Windham needed to be aligned. However, unlike the DRD, the Windham’s handguard is attached to the upper receiver so you need to look through the handguard to ensure the gas tube clings with its hole.

These are three stow and go ARs that offer ease of use and compact portability.

Takedown Component Dimensions DRD Tactical DR-15 Ruger SR-556 Takedown Windham Weaponry Model RMCS-4
Rail or Upper/Rail Length 13 in. 18.5 in. 15 in.
Lower Length 16 in. 15.75 in. 15 in.
Barrel Length 19 in. (w/ end cap) 17.87 in. 18.75 in.

Note: Typical AR-15s with 16-in. barrels have an upper receiver that is 24.5 in.—depending on muzzle device—and a lower receiver that is 15.75 in.—depending on the type of stock.

Do you have a stow-and-go AR-15? Which model and for what purpose would you own a takedown AR-15? Share your answers in the comment section.

The Mission of Cheaper Than Dirt!'s blog. "The Shooter's Log", is to provide information - not opinions - to our customers and the shooting community. We want you, our readers, to be able to make informed decicions. The information provided here does not represent the views of Cheaper Than Dirt!

Comments (19)

  1. Thats a good question and the why I started out… Before getting my Ruger Sr556 300BO barrel, I had to carried a complete 300BO 8.5″ pistol upper, which accomplished what we both thought would work but several issues surfaced. First was weight and the size, it was twice heavy as the Ruger 300BO barrel and because of size couldn’t be stored at all in the carry bag barrel pouch let alone with the 556 barrel. It ended up in the fold between the lower and barrel compartments. Assembly time was about the same, give or take a couple of seconds, unless I was shooting both 556 and 300, then switching out the Ruger barrels is 2-seconds. For me, as a SR556 Fanboy, I really appreciate the engineering that went into designing the Ruger and most of all, I have yet to find a 300BO upper that shoots as smoothly or accurately…

  2. Makes good sense?

    Actually, it makes no sense. Why spend hundreds more for something like this, when a simple AR pistol with a brace does the same job?

  3. I would rather have the 10.3″ barreled pistol with a Law Tactical folding buttstock adapter that I built for half to less tha 3/4 of what these costs. Fits in a backpack that I routinely carry in public.

  4. For that, you can get a sub 2k or a micro roni. Granted the 2k is a carbine but it just flips open and its less than 17″ folded.

    For 9mm you cant go wrong either way except that in many states you cant legally conceal a carbine.

    The breakdown ar’s will never be in my safe unless one is given to me free.

  5. I own the Ruger SR 556 with the 300 Blackout barrel and absolutely love it! The one big drawback is the cost: Without the 300BO barrel, Ruger wants over $2K, online resellers around $1500 to +/-$1300. Takedown or re-assembly is really 10 seconds or less… You can flip out the 556 barrel for the 300BO in less than 3-seconds. I like the 300BO 200 grain subsonic best for suppressed and mostly keep it that way, leaving the 556 at home unless I’m out plinking. It is a piston gun, which when supressed keeps nearly all the gasses at the end of the barrel and away from blowing back in your face like impinged systems, which the other two are… Also has an adjustable gas-block that lets you dial in your favorite ammo or barrel configuration (suppressed or not). Versatility in ammo with minimal reconfiguration, easy and simplicity of takedown-reassemble-recongiguration, takedown compacness and last but not least portability. For me it was well worth the money!

  6. The negligible (in my opinion) difference in length compared to a regular disassembled 16in barrel ar isn’t worth it. If you want to go even smaller a ar pistol assembled or not would still be faster possibly smaller and more affordable.

Your email address will not be published. Required fields are marked *

Time limit exceeded. Please click the reload button and complete the captcha once again.

Your discussions, feedback and comments are welcome here as long as they are relevant and insightful. Please be respectful of others. We reserve the right to edit as appropriate, delete profane, harassing, abusive and spam comments or posts, and block repeat offenders. All comments are held for moderation and will appear after approval.