Works fine on a Mossy 20 ga too. The recoil pad is a monster to remove. Be careful or you can strip the screws. Fits my Mossy perfectly. There's a little gap at the trigger guard, but it doesn't look bad. Not a beefy as the factory poly stock, but certainly good enough. Great ergonomics.

Not bad for the price. The directions took a little time to get through but once it was done it took 15 mins. Would have given 5 stars but apperance was a little off. In all it fits tight and appears stable.

Awesome product. Installed simply and looks great on my Mossberg 500. Fits really well in the shoulder and gives great sight alignment for factory or Red Dot sights.

I bought this stock because I could use it on my Mossberg or my Remington, well . . . I should've known better but the universal stocks don't really fit well on any of the shotguns they're meant for . . . There was a huge gap between the grip and the reciever when it was on my Mossberg and I couldn't put it on the 870 because the bolt from my wooden stock is too long to secure this stock . . . That being said, I sized it up to decide if it was worth making a trip to hardware store around the corner and it's not . . . They give you all kinds of cheap plastic crap adapters with this for doing all kinds of different things but the bottom line I think is that ATI needs to more concerned with making their products a better fit on the individual weapons than making sure they fit on ten different shotguns so more people will buy their garbage products . . . The worst part? I realized all of this AFTER I bought two of the five round shell carriers, drilled holes in the stock and mounted them on both sides . . . They tell you specifically not to overtighten any screws in the instructions because the screws are crap and will strip very easily (I'm not sure there's even such a thing as a poor quality screw but ATI has them!) . . . There are so many other options out there and your gun deserves better than an ATI stock . . . A lot of my time and money wasted . . .

This shot gun stock came with the buttpad screws so tight that I stripped one of the screws trying to get it out to install the stock bolt. The screws are the cheapest possible garbage. The spacer feels flimsy and the directions are vague at best. Spend a few more bucks and get something that isnt cheap junk.

This is an awesome grip. It is super simple and took me 10 minutes to switch out on my 870. It is really solid and really comfortable. Thanks for the fast shipping CTD!

This is a Great stock. I have had it for 6 months and it is still on my Mossberg.

This has been a good stock for my Moss-500. It seems to ballance the gun well. You can realy cycle the rounds.

I’ve got time, tools and a wide variety of materials available to me. Unfortunately I don’t have much cash so I’m very happy with the price (4 stars) well actually 3 is for the stock and 1 is for the free kick ass catalogue they sent. My bench was ready for this sucker the moment it landed on my doorstep! Poor thing never stood a chance; Firstly I knew that I would be taking this thing apart every time for cleaning and didn’t want to hassle with about 5 pieces and the bolt so I glued them all together and fitted it, then once dry took it apart, now to put it on I’m only dealing with the bolt and the stock! I padded the back of the grip or thumb arch area out with about ¾” dense foam and then put a grip cover over it which hides the foam and has widened the whole grip; it feels beautiful even without shooting gloves on. I cut, re molded and fitted my Remington Supercell buttpad onto this as the original is not good, also I made a cheek pad and glued it directly on to the top of the stock and modified an elastic 6 shell holder for the stock.

I've had this stock on my Remington 870 for a few months now. I've fired about 50 shells (2 3/4" target loads mostly and some 3" mags) since installing it and I've had no issues at all . . . The gap between the grip and the trigger guard that some people have mentioned is insignificant, especially compared to what you end up with on a Speedfeed stock and this costs half as much. The grip itself is comfortable and the stock is very slim but it's also very sturdy. I would have honestly preferred something with a bit more substance to it, like the Benelli pistol grips or more like the Remington factory stock but for this price I couldn't ask for a better product . . . It looks good on my weapon too! I would suggest replacing the recoil pad if you're not a seasoned shotgun man . . . I've been firing 12 gauge for sport for years and I handle it very well but my girlfriend and brother thought this particular stock didn't offer much in the way of recoil reduction and consequently, wouldn't shoot with it for long. Again though, this is an excellent product for what you pay.

This stock is a perfect fit on my Maverick 88. Very easy to put on.

I bought this for my mossberg 500 it looks great easy to install

This is a great stock it fit perfectly on my mossberg 500 persuader with no gap. It handels much better and looks awesome. Stock feels very solid and goes on easy thinking about buying one for my winchester 1300.

this is by far the best stock for the money... it isnt as good as a knoxx spec ops but.. it also isnt $120 eather. i mounted it on a new england pardner protector (870 clone) i had to trim the spacer to 1 1/4 inch but that wasnt hard all i used was a dremal tool with a cutting attachment. it looks nice feels great when you shoot and fits well. the lines where they attached the 2 halves of the stock sticks up a little bit and is kind of sharp but again dremal tool with a sanding attachment. but all is expected with only paying this price. i would recommend!!

Looks awesome. Fits perfect. Hardest part was getting the stock bolt off from the gun. Had to use a ratchet. I have maverick 88.

Just bought one of these yesterday for my mossberg 500a. When one very easily, is rock solid, and looks GREAT!!

This stock went perfect onto my Defender 982. I was a little worried becuase it is not one of the popular brands such as Remington and Mossberg, however it went on smoothly and holds nice and tight no wiggling and easy installation.

This was solid on my 20 gauge Mossberg Bantam. Only thing I didnt like is the screws on the recoil pad are SUPER TIGHT. The forend by ATI doesnt fit the shorter Bantam slide. Oh yea IF you dissassemble the gun stock has to come off-once a year thing for me though.

Very simple to install,great price. Bolted right up to my 500 with no issues.

check the screw hole that holds the buttplate the on i just got has a hairline crack that is very hard to see put some super glue on it havent tried it yet hope it holds everything else was perfect overall satisfied

i just got mine on the 870, havent shot it yet but it looks good and makes the gun easyer to handle, only took minor fitting to loose the gap you get with the 870. but all and all well worth the money i think.

i bought this off this site. it makes my mossberg 500 persuader look very mean and tactical. the control of the gun was greatly approved. it fit so well that the gun looks like it was origanlly made with this stock. i ran into only two very very minor problems while installing. the frist was that the two parts that were suppose to go together didnt fit. that was easily fixed by taking the burrs off the plastic peices with just little knife. the second problem was that the orignal screw will not work if you are converting from a pistol grip. you have to go to the hardware store and get a 5 1/2" bolt to make it work. so for a total of 58 cents its not a big deal. if you want control of your gun theres no better way to go id recommend to anyone.

So you own a 12ga and are looking to modify it. If you choose just a pistol grip, good luck firing multiple rounds of tactical ammo. This option gives you a shoulder stock [a necessity in 12ga] and a comfortable p-grip. Could you buttstroke an enemy out of commision? Maybe, it feels solid enough but I have yet to try it out. It does reduce the felt recoil on my wrist bones though, and in the "heat" of the moment I doubt you'll notice anyways. It will fit my 1300 [Big Casino]and my Maverick [the Hoff]. It stays on the 1300 with a heatshield and a few extra rounds on a buttstock shell holder. The Maverick is a entry level type of firearm and so I modified a used p-grip to fit it for in car applications where size and mobility are an issue. Better than a plain P-grip in my opinion. USMC

Installed on my Mossberg 500 with no issues at all. Good solid fit and doesn't leave any open gaps. The pistol grip is angled a bit futher back than I would like, and where it meets the main stock is uncomfortably thin - but it's not bad enough to go back to stock. It does make it easier to manage a heavy shotgun...

I had a pistol grip on my Moss 500 and it nearly broke my hand on every shot of buck or slug. I replaced it with this PG Buttstock and it fit beautifully without an adapter. Gave the gun a much more tactical look and feel. GREAT BUY! Though if you are replacing a regular pistol grip like I did you will have to buy a longer bolt to attach. 28cents at any hardware store.

For the money I spent I think it is a good deal. It has the right shape and fits well. There is probably a better combination of functionality, quality and fit but I think this is worth buying.

original bought for my Remington then changed my mind and put it on my Mossberg. nice. makes my mossy look tough and tactical ready. fit real good no problems mounting.

very good stock. looks awesome, gives really good control of the gun. as others have mentioned, it does lack a little in the padding department. not too big a deal for me. the stock fit seamlessly onto my Mossberg 88, it looks like it would have came from the factory like this. a must have for all shotgun aficionados.

this is a great stock, gives you more control over the gun. Yes it did leave a small gap between the adapter and gun on my rem. 870 but heres the trick take and file the adapter down until it fits flush with the gun, with a good file it only takes a short time.

I mounted this on my Mossberg M500 having had a standard synthetic stock on it before. I shoot my gun aggressively. Tactical target courses, 6 clay reports. It gets a work out. There is a noticeable increase in control of the weapon. I feel as though its a more natural position to shoot with. It's a great accessory. There's only one flaw I have noticed, if you can even call it a flaw. I feel as though I had to really crank the bolt down to make it solid, but it's only a minor thing. Overall well worth the money. Great Investment.

I put this stock on my NEF Pardner Pump! It looks great. There is a gap, as mentioned by the others, but it makes it look like a new gun. Great ATI stock.

I installed on a Remington 870 Marine Magnum. This is a good price for the pistol grip. Slight draw backs are it does leave a little bit of a gap where it meets the gun. (as mentioned before) Also, the padded but is really not that forgiving. The gun originally came with a gel like pad. Very nice for recoil. This one is padded but not nearly as nice as original. Sadly the original pad is just a little to large to install on this one. In the end I am going to keep it. CTD does offer the best price for this and it is the best for this price range.

this stock is very solid and i feel like i have alot more control with the pistol grip, it is actually i tad heavier than my wooden one...the only thing i don't like is that theres a tiny space between the stock and the shotgun.