Bought this for my Romanian SAR-2 (AK-74) and I liked it very much. The only thing I didn't like was that it makes the stock considerably longer even when in the fully collapsed position. Other than that it's a great product. I'd definitely recommend it to anyone.

This is a very good quality package. I had a friend with me when I installed this which was helpful. The parts fit tightly and feel strong. The instructions in reference to the upper forearm could be better. When you replace the upper forearm, place the metal end in a vise, grip the wood and turn it like a motorcycle throttle. The wood will spin right out of the metal housing then spin the new one in. Other than that, take your time, relax and enjoy your new looking rifle!

Looks good fills good.It fit good on my MOD:GP 1975 with a little filling thanks CTD.I love it.

After reading lots of reviews on different products and debating whether or not to replace my OEM stock, I went with this one even though there are some negative reviews. I installed it on a WASR 10/63 7.62x39. First the install: It came with somewhat vague instructions. Some parts are detailed on the break down of old parts some are not. Goes into great details about how to mark and drill stock and recommend pilot holes. I just stuck the new stock in and drilled the final size hole right into it and stuck the screws in (use proper size flat head: they go in for the first time incredibly hard). It fits great and tight. As far as the stock overall it is the only part I have issues with. There is a small amount of slop in it where it extends and makes a little noise. I am a huge man 6'4" and the only place this feels comfortable is in the fully collapsed position. Next, attaching the grip: it comes with a plastic replacement for your stock metal threaded piece. I used the OEM one, same issues as everyone does not thread in as far as it should seems fine though I really cranked it down hard and it didn't strip. Held it with one hand firing it (stock folded) and was pretty solid. I would opt for a little longer screw if i could get one cheap. Now for the part that scared me the most: the handgaurds. The top one was easy: twist the old one off and twist the new one on. I tried to use the metal piece that was in the old one to assure a tight fit but made it bulged out on the sides. It wasn't necessary. It fits great without it. The bottom one did require me to grind off the tabs on the side and is detailed in the directions i used a die grinder and it came right off. The rear of it that attaches to the receiver sides needed to be filed down a little for a tight and good fit. I was worried about it being sloppy but it was nice and tight. I took it to the range and put about 300 rounds though it with no issues. It was 95 degrees in direct sunlight. My buddies AK wood was hot and the wood was starting to burn on the end a bit, mine had no issues i was worried the plastic would start melting but it was okay. I wish the handgaurd rails were metal but they are pretty tough plastic. I like that the cleaning rod will still go back in with this handgaurd. I heard on some TAPCO ones it will not. One thing that I really don't like is that i use a UTG quick release rail scope mount that goes on the side receiver rail of the rifle. When the stock is folded it will not lock or completely clear the bulkiness of the scope mount. It will kind of lock without the cheek rest but will not lock at all with it on. Also those quick release style ones will not clear the stock to the slide off or on because its bulging out where the lock for the folding part is. I might have to get a scope mount system like the integrated dust cover one or something. Overall for the price it cant be beat.

I must say that this was a fantastic purchase. I have a WASR-10 and granted the kit did need modified but it can be done. Don't let some of the bad reviews fool you. Everything went smooth except for the hand rest like others have pointed out. I did some cutting with a blade and after about an hour I got it just right. This is a solid feeling piece of equipment and I am happy I purchased it. No regrets.

I have a lot of experience around combat, plenty of trigger time, and this stock will not last. The forend is decent, but the screws need a dab of loc-tite to stay in place. I also had to do a little dremmel work to get it to fit. The groves in the molding dont line up with the metal parts of the rifle. The stock is hollow where it attaches to the end of the rifle, so after a few training sessions it will become loose. Since it's plastic, there's nothing you can do. Spend a little more money and get a metal stock.

I can't tell you how great of a buy this is. It looked very nice and fit tight. There was a little filing and a little help with a razor blade to make it fit very nice. Usually with all guns, you have a little minor adjustments needed with stuff like this. I'll tell u one thing, this makes my AK look sweet and feel solid. Thank You

Put this on my Romanian WASR 10. Fits snug after a little shaving with a knife and a die grinder on the lower handgaurd, no rattle or play. The stock could be a little shorter but I actually like it fully extended, makes me hold it tighter and more steady for me. I don't have a big arm span. The pistol grip makes my gun feel 10x better and I got it in under 5 days. CTD awesome shipping. Will be buying more from this site, lots more.

This is a heck of a stock. Rock solid, provides a much better shooting platform than the original AK design. Installing was simple. The filing was the only hard part. Glass-filled nylon is just about indestructable. If you have to file to fit, just be ready for a good work out. But overall, this stock is perfect to transform your AK into a modern tactical rifle.

Thank you CTD for fast shipping! AK: Roman WASRD-10 threaded. STOCK: Bit heavier than expected, thou no turn off. Fit like glove, no filing needed. Is very comfortable. Solid, no rattle. Cheek rest made it feel a bit to large. Forend (Lower guard): minor filing/both ends, NOT much, go slow! solid. Rails (though plastic) are nice bonus. UPPER GUARD: minor filing or cutting of 6 "ribs" protruding from bottom. GRIP: IS great, big improvement from standard! EXC! I used the grip screw + bolt from old grip. It works. the plastic grip bolt that is intended to hold grip to rifle seems very weak. Didn't trust it, used original metal one. I will order new longer grip screw, thou for now the original does work thou its about 1mm short of threading thru other end of grip bolt. Screws in about 95%. OVERALL: looks good, feels solid, comfortable. CTD shipped very fast. My 2 cents.

I bought this kit and I am not very happy. The butt and grip went on okay, even though the butt is very loose and the hinge for folding. It vibrates alot and makes noise. The rest needed alot of grinding. To much to make it look right. Other people may not be able to notice it with out looking hard but I can. I am not happy with this product.

I bought this kit for my Norinco 84-S. Anybody who has one of these knows that aftermarket parts are almost impossible to find. It is the 5.56 version norinco AK. Anyways, the pistol grip went on with no trouble at all. Same with upper hand guard. I did some very minor filing on the buttstock where it slides into the receiver. No bid deal there. The collapsible buttstock is kind of pointless in my opinion, since any setting other than the first makes the gun too long to hold comfortably. The hardest part was modifying the lower hand guard. I am a little bit mechanically inclined, but I've never done any gunsmithing at all. However, in about 10 minutes with a dremel tool, I had it whipped and back on the gun. I just had to deepen the grooves where the metal pieces mate to the plastic. I will say that the upper and lower handguards are just barely out of alignment, but I would guess that's my bad smithing, not a flaw in the product. One thing to keep in mind, reassemble the gun with the cleaning rod in place or you will never get it back in correctly. The kit was missing one rail and some small hardware, but because of the folding stock I don't plan on using a rail that side anyway. I'm sure if I sent an email to ATI they'd replace the rail. All in all I think it is a nice kit. Now if I could just find hi cap mags for this model AK...

I've had this stock on my Chinese Norinco MAK-90 for some time now and thought I'd review it for other's thinking of buying it. If you really want to wake up your AK, then this is the stock to do it with IMO. Compared to the silly thumbhole stock it came with and even the ridiculously short wooden pistol grip set I had tried too...I finally have THE stock for my AK. It is so comfortable to shoulder and shoot and if you own or are used to an AR platform, its even that more compatible. Initial fitment took some trimming/fitting but hey, isn't that part of modding and gunsmithing! After about 1000 rnds down range, this stock still locks up tight as a drum and makes shooting my AK a pleasure. A few things to point out: *Even at 6'5" with long arms, any adjustment beyond fully collapsed is useless...just too long to shoulder. So even fully retracted this stock may have too much LOP for short/small armed folks. *The molded picattiny rails were razor sharp..needed to debur the edges and corners before installation/use. *Can be fired while folded but mag removal/insertion is awkward. *Keep in mind 922R requires 5 U.S. made parts if you put this folder on your NON-Threaded AK...six U.S. parts if it has a threaded barrel. This stock counts as 3. I simply use U.S. made Tapco magazines, which count as 3 parts as well to stay compliant.

I have 2 AK's. One I kept original, and one I decked out in this awesome kit. It was pretty easy even for a novice like me to install. It looks MEAN, feels GREAT! I now call them "the Kalashnikov sisters"

Installed this on a Norinco MAK with a straight cut receiver. With a little filing it fits great and looks awesome!

Great fit, Almost no work fiting on a Romania wasr, no Play in stock.

This kit impressed me. With minor fitting it fit perfectly. It looks sharp and works even better. If get a front grip with it most of your barrel lash disappears. Tip top.

This is a great kit, I have a Romainian AK and the buttstock went right on with no filing at all. I just slid it in, drilled the holes and done. It's probably better the the buttstock doesn't have pre-drilled holes because AKs aren't real consistent on tolerances and pre-drilled holes would probably cause a lot of alignment issues. As for the lower Handguard, it only needed a small amount of filing and it fit great, and the upper guard didn't need any filing at all, and as for the grip bolt mine was only short by about 2 threads, it fit fine. I think it feels and looks great. I give it 5 bullets easy.

Gotto start with delivery, awsome! I used standard shiping and it was here in three days. As for the parts they will do just fine. Ive got a Romanian WARS-10 and after a little dremel wrk had a good solid fit. The stock took some getting used to its a little longer due to the folding mech. Not bad for the money, I'm good to go. Makes for mean looking rifle.

Fit my stamped Interarms AK fine with a little filing on the butt stock. all other pieces fit perfectly, The Ak by nature will be slightly different from one gun to the next which cant be blamed on an after market add on. For those with issues with the pistol grip bolt a quick trip to the hardware store will fix that, mine worked fine. only MINOR issue in my eyes is slight play in the stock, I mean VERY slight, for the price cant be beat and I recomend it to all AK owners, improves handling & comfort and looks great too!

Great set. I was worried about the price being to cheap, and getting what i paid for, but I was amazed by how well built and easy to install this kit was. I would definitely recomend this kit.

Installed easy in my WSAR10 in about a half hour. I had to trim down the rear inner rib on each side of the lower handguard about 1/16th of an inch in order to get it to slide into place properly, which the instructions pointed out may be needed to install on some guns. Looks great, works great, and was more that I was hoping for!

I couldnt find a folding stock anywhere for a milled receiver. I have a Bulgarian arsenal SA92 and after looking at the pictures of this package I figured I would take a chance and see if I could make it work.After about 3 hours in the shop using panel saw and air grinder had all assembled and lookin great. Very solid . Only complaint is cheek plate to low but no big deak.

Well, I have been contemplating this purchase for some time! I now have 2 AK's in my collection. One is complete factory hardware and now one dressed up with this awesome set. Mine came quickly and I was ready for the install. MY hand grip was the easiest part to install. The screw was the perfect size and was done in no time. I had troubles removing the wooden hardware, but after a little browsing on the web, there were plenty of sites to help explain how to do it. A little filing here and there, some light hammering, and this thing is on and looking mean! Great purchase!

Great set, Had a couple of issues putting together but mostly easy. I also had to grind the ribs down on the upper hand guard, only took a minute. Shoulder stock is long and a little on the heavy side but the folding feature is nice. Grip feels great in the hand. 5 Stars...

1) Super fast shipping. 2) Product arrived as descibed in perfect condition. 3) Pistol grip - Mounted perfectly to my Romainian stamped AK. I used the existing grip bolt on my weapon to mount. It worked perfectly. After reading other reviews I feel I must have gotten lucky. 4) Gas tube cover - Mounted easily with no modification. Looks great and functions perfectly. 5) Foregrip - As other reviewers have stated, about 15 to 30 minutes with a Dremmel and the parts fits well. If you have any mechanical ability this should not be a problem. 6) Buttstock - Easy to mount. Solid. Heavier than I like, but I new that before it was purchased. Functions great and looks awesome.

Bought this kit read all the great reviews maby I got a bad one but there is a lot of vertical play in the stock horizontaly very solid.then the little screws that hold the cheek rest were prestriped but it dosnt seem to matter the rest locks in preatty well the front grip need some cutting to fitt but once it was on was sturdy the hand gripp hasn't bin put on it does not have the right bolt but no surpries from other reviews but it also just feels weired so Im leaveing the Tapco saw grip on it feels great. overall seems like a cheap kit and a lot heavier than the tapco set my I.O. ak came with.

Well this is definitely a bad-ass stock. No question about that. And it didn't require much work to get on either. ( you will have to drill lead holes for the screws holding the stock on). Other than that, it fits my WASR-10 like a glove. My only complaint is that the material feels rather cheap. Or at least cheaper than I was expecting. Took them shooting today and had 0 problems though. So can't knock the way it feels since there have been no problems with it.

The stock fit my WASR 10 like a glove. Like a lot of others I had a hard time getting an appropriate sized bolt for the grip. Home Depot and True Value had nothing metric. I got lucky and found a Tapco AK grip screw at a local gun shop that did the trick. With the kit in place I was very impressed with how solid the stock felt and how well the rifle handles after the upgrade. I had been pretty happy with my fiber force stock but this blasts it out of the water. Totally worth the money, just make sure to wrangle yourself a Tapco grip screw before you try to install the grip.

(Mak-90)I read all the reviews and was going into this purchase with both eyes open. I knew there would be filing issues and bolt issues, but i really felt that this couldn't be as difficult as some were making it out to be. Well, i ordered and it was here in only a couple of days. (thanks CTD) The forearm actually went on easier than the wooden one. NO filing for top forearm and only two ribs for lower. Fits tight and i am confident it will securely hold the Aim Point it now possesses. The folding stock was a little more challenging. It took a little more filing, but is extremely secure. (Under file, not too much) Pistol grip was the expected problem. Don't go to Lowes or Ace. You won't find any 6mm bolts. You can order a longer bolt of course, but i was too impatient for that. The bolt actually touches the nut, but it's not long enought to thread. I took my pistol grip to my belt sander and sanded off about an 8th of an inch. Works great. Awesome feel and looks bad ass. Would have gotten 5 bullets if they supplied a longer bolt.

Love this kit. Installed on my WASR-10 in about 45 min. Handle bolt worked perfect on my gun. little bit of filing w/ my die grinder and it was a perfect fit. makes the gun more functional for a tall lengthy guy since the butt extends soo far. I love this kit. Thanx CTD. not to mention it looks 1000 times better.

great product,but like lots of other people the grip bolt was hard to find. bolt depot.com has a number of sizes to fit any needs hope this helps everyone out.

Bought this from CTD & installed it a few days ago on my WASR-10. It's rock solid & feels better and more sturdy than the original wood furniture. It's very easy to install, and just in case yours doesn't come with all the necessary paperwork (mine was missing the exploded parts diagram), you can get it on ATI's web site. It has 3 optional Picatinny rails on the foregrip. The pistol grip is a huge improvement over the rectangular plastic WASR-10 one. The stock is rock solid, increases the available length of pull with 6 retractable positions, and also folds solidly to the side with no wobble. This product also made my WASR-10 look a heck of a lot cooler. It's more ergonomic, more solid, and more customizable than the wood furniture. I highly recommend it if you have a stamped, semi-auto AK clone with wood furniture.

I have a GP WASR10 and this is was a great buy to dress up the gun with. STOCK: Better than my wood one. Adjustable! Won't collapse when you shoot it like the tapco one. Folds well (even has instructions to modify it if your gun doesn't meet compliance yet). Drill two holes and put the screws in, you're done! The hard part was getting the wood stock off. PISTOL GRIP: I actually couldn't use it because I don't have the stock screw that comes with the gun... so you need that. BOTTOM HANDGUARD: Awesome. You can put up to 3 rails on it and there's covers if you don't. Takes some time to figure out getting it on, instructions say you might have to file down two molding ribs and that's just what I had to do but the hard part was getting the end of it into the gun. I had to pry it and hit it with a rubber hammer to get it seated correctly. You'll figure it out... UPPER HANDGUARD: Bizzare. Mine had little "things" on it I had to break off to get it to fit. Probably just extra molding from the manufacture process. Turns onto the gastube easier than the wood did! Hard to get the hex screw in though, you have to hold it on top and bottom so the nut doesn't fall out. A bit hard to level the cant (for me but I'm a 'tard). This seems like the thing to buy, everything works right when firing. Cheek-rest is kinda hard on the buttstock but whatever.

After reading a few of the reviews here I was hesitant to purchase this item, but I needed something to replace the crappy Dragunov Fiberforce stock (which really sucks and looks cheap). So I bought one of these to put on my Chineese made NHM-91. CTD shipped it to me quickly and I began my task, keeping everyone's review comments in mind. I used the Dremel tool and a razor knife to remove the ribs on the stock and applied a little bar soap. It went right in and fit well and tight. Remember, depending on your variant, remove the ribs a little at a time to maintain the tightest fit you can. I drilled the screw holes and put in the funny looking screw common to AKs. I left the pistol grip for later as I knew from past reviews that the screw would not be long enogh. The lower handguard went in easy after I removed the ribs and wrestled with it a little. The upper handguard was a little more tricky - put it in a vise and it will be a lot easier. Now back to the pistol grip. I looked high and low for a 6mm bolt that was about 5 inches long. Home Depot, Lowe's and even a local Fastener and Tool Shop - no luck. My last hope was the local Ace Hardware store, but I learned that nobody makes a 6mm bolt or screw that long. There was a happy ending to this story though. While repeating to myself, "I can't believe nobody makes a bolt that long, my eyes fell on the descriptions on two of the drawers and a plan came to mind. Here is what you need to do. Ace sells 6mm studs about 3.5 - 4 inches long and in the same area it sells something called a coupling, which looks like a nut but about an inch long (6mm of course). I bought both and took them home. I put my original pistol grip screw in the bottom of the pistol grip, i screwed the coupling onto the stud and screwed that on to the pistol grip screw from the top of the grip. I placed it onto the weapon and through the hole where teh angled nut goes. I marked it and then ground it down to size. It makes the 5 inch screw you need and works well. Good solid product, 4 bullets instead of 5 because they should include a long enough screw.

My brother bought this AT Strikeforce kit and it looks great after I got rid of the thumbhole stock on my MAK-90 .223. The Mak-90 had and stamp reciever and is slightly slanted end of the reciever. You have to file off the ribs with the dremmel to make sure it fits. There is a little gap where the slant is but it doesn't look too bad. The forehand and gas tube cover is fairly easy to install after filing off the two ribs with a dremel. The installation of the grip required buying a new 1/4" x 4.5 " bolt at Lowe's. You have to retap the threads on the other end in order for the bolt to fit. Also I had to widen the hole at the botton of the grip to recess the bolt . After 3 hrs of work , the MAK-90 .223 looks menacing. I installed the 30mm Tasco red dot reflex sight on the hand gas cover mounts. Everything looks great. The stock is still long even in the closed position but I shorten it 1" by removing the rubber pad. Overall, the stocks perform great , comfortable to operate but heavier in weight than the wooden one.

Stock does what it says at a great price. Grip is awesome. Hand guards went on with some trimming not difficult to install at all. Only thing i dont like is buttstock is not very functional in folded position as it gets in way of trigger finger and is very heavy, I wish i would have went TAPCO on the folding stock. For the part time shooter its worth it though. If you shoot alot go TAPCO.

Awesome lower hand guard took a lot of filing but I just took my time and it fits nicely. Stock slipped right on drilled two pilot holes and screwed in place. About 1.5 hours for the install on a Romanian stamped AK. 4 Bullets

Good solid stock, but way too long. Spent a couple hours and replaced the folding part with homemade steel part and it makes a good stock. Still only need the first three positions before it is too long. Original folding part sticking out the side is right where it will smack you in the face under recoil.

I just received and installed my "Strikeforce Kit" on my stamped Romanian AK variant. It went on, just as advertised, with a tiny amount of Dremel work necessary to get the correct fit. The added length of pull is OUTSTANDING!!! The adjustablilty factor is also a definate plus. Although this kit looks like it belongs on an AR platform rifle, its functionality on the AK is top notch. The handguards required slightly more tooling to get the correct fit, but after only about a half an hour everything was on nice and tightly. The two inner ribs closest to the sight block need to be removed like in the instructions, but other than that, this kit makes any AK more functional. I didn't have to install the pistol grip because I had already upgraded to a modular CAA one, so I cannot attest to the difficulty of installing that piece, but the consensus seems to be that a longer bolt is required. All in all, I really like the Strikeforce package. I would hope that eventually they will be offered in additional colors, but for now, mine is being USED quite a lot!!!

Some of you must be awful lucky. The bolt is too short and I went to 3 different places to find one,(6M x 1.0 X 110MM). Cannot find a bolt. Anyone know where to find one? Got the stock in except for about 1/16 inch. Put oil on it and can't get it in or out. As for shipping, it took 11 days and I live in a city. It stayed in Grove City Ohio for 8 days. I haven't even tried the handguards yet, can't wait. Like the other guy said, don't laugh, I have a Mak90. Any ideas about the bolt would be appreciated.

This collapsible, folding stock is really high quality. Adjustable cheek rest. The install was easy on mine, it fit perfectly with no grinding.

Bought this for my ak and was alittle let down.after reading other reviews i knew what to expect but let me tell you more. You have to file 2 ribs on the lower handguard(no prob) the handguard fits up VERY nice.The bolt for the grip is to short(which they dont tell you)Now the stock is a totally different story.this does not fit correctly for the a stamped and slated reciever.I had to do alot of filing and I fear that it may have compromised the integrity of the stock.The stock at it shortest is still about an inch longer than the original stock and when it is pulled out it is not practical.the handguard is what gives this the 3 shells. If you have a stamped and non-slated reciever this will work great.If not it will not look as professinal and may be less durable..Good luck..

I got this set for my Egyptian made AK. It went on in about a half hour with very little grinding. The pistol grip is alot better than the factory grip. I would suggest this kit to everybody that owns an AK. A friend took one look at my AK and decided to order one for himself.

nice item .....had to do a little fitting. only down side is that the hand guards have to be removed to add/ remove rails.

this set is awsome... it only required a little bit of modification and only took me about 30 mins to get everything on it. well worth the money CTD has some wicked shipping it got here super fast and everything was in great condition. it made my romac AK47 look great. GREAT BUY i dont care what anyone says if u havea AK and u want it to stand out buy this kit. GREAT DEAL!!!!!

This kit is great. Took about an hour to put on my WASR-10, had no issues except I had to dremel out a couple ribs in the bottom hand gaurd. My AK looks amazing, and is now more solid and functional (the old stock was to short and small). I will be recommending this kit to all my friends.

Great Upgrade! Improved the overall feel of the weapon. The stock itself is worth the price just for the added stability. It did take a bit of work to get get everything installed. I had to break out the dremel to get the front handguards on, but I don't mind a little work. Was shooting 4 inch groups in the bulls-eye at 100yds with iron sights, so I'm happy!

Performs well,I am pleased with the outcome of this product. Some filing is required, but not much. stock is an inch longer than the original, but I'm tall so it was a plus for me. It seems during live fire the stock absorbs more recoil than the orginal wooden stock."my opinion" Highly reconmend this to anyone who is a ak lover. I'll rate this product 10 bullets+.

Very strong stock! I think it is far more durable and actually weighs considerably more than the wood I took off. However, the six position stock at its shortest is still about an inch longer than the original. Someone would have to be about 10 feet tall to use the stock completely extended--I found all but the shortest position to be to long. This stock really bulks up the gun and looks sexy, but is almost to big and bulky to make the folding / collapsing stock advantagious.

i bought this stock after debating which one to buy i ended up buying the ati strike force pakage when i got it the lower handgaurd with the pakage was misshapen and would not work. i ordered another handguard assembly with a couple of pocket knife shavings on some polymer mould lines. now it fits tight, no wobbles and makes my ak modular allowing lights and lasers. note that this stock does not shave valuble pounds from your ak as it is actually heavier than wood. never the less i am more than satisfied, and had the first lower handgaurd worked it would be a 5 bullet review.

purchased for my MAK-90. a little filing to be done, but looks and feels great. Really worth the price. I recommend that if you have a mak 90 with the fiber force stock, to order the longer pistol grip screw, along with this stock.

Just a little grinding with my dremel and BAM instant improvement! My buddies are very impressed with the kit also. Dwayne

Thank you for offering such an incredible product. Just finished the change-over of my WASR and I am thrilled with the results. It looks great and feels fantastic. The original stock was too short for my liking, but the new one is a perfect fit. The adjustable cheek rest fine tuned the weld point beautifully. The minimal filing that was necessary was no problem - it only ensured a customized fit to my rifle. Fantasic product for a reasonable cost.

It took a little filing on handguard but other than that its great. Definitely worth 90 bucks. Enjoy!

very well made!!! looks and works great !!!! installed it in about two hours (realy took my time) small amount of filing to make it fit, well worth the time if you own an AK try one you'll love it thanks guys DJ

Looks sick on my mak-90. installed easily except top foregrip because my dog chewed it. Dont laugh at me I have a mak-90,lol. You have to file a little bit of plastic,simple with sandpaper and a Buck knife.

I like the way it feels in my hands. I like the way it looks. I dont like the fact that i need to buy a longer bolt.(that is the reason for only 4 bullets.)But over all i am extreamly happy with kit.

had to tweak it a bit but nothing anyone with some commonsense and a dremel can't handle, got it for my mac-90 works great, nice and solid, not shaky at all had to get a new bolt though for the handle went to Lowe's got a 4 and half inch or five inch bolt can't remember went standard 1/4'' with the bolt so i had to retap the nut on the inside of the gun to make it work then filed down the edges of the bolt and cut a notch in it to make it fit into the handle and be able to tighten it down, like i said not to much work for a good reliable stock i would recommend it to a friend.also i learned alot about how the ak style fits together, thought it was real interesting.

I got the stock set a couple of days ago. Great, easy, speedy delivery by Cheaper Than Dirt. This was my first CTD purchase but it will NOT be my last. This stock/grips set was WAY higher quality than I had expected. For what this stuff costs, I half expected a cheap feeling plastic but it's not that at all. It has good weight, the stock telescopes to a great variety of sizes. I did have a little trouble getting the foregrip and the gas tube covering on but I think it was because of a tool shortage on my part (I think I need a bench rest and feel pretty sure I could have done it). The stock and pistol grip went on fine but, rather than risk messing it up, I took it to my LGS to get them to put the others on. All in all, I'm very, very impressed.

Just installed my new AK Strikeforce Stock set up, well trying to install it. Appears to be very nice and solid, but had a couple of issue's with the install. First there was no screw to attach the hand grip, which required a additional purchase, which i'm still waiting for. This screw/bolt should have been included or at least suggested. The upper handrail was to long and had to be sand down to fit, took about 1 hour of very careful sanding to make it fit. Other wise it's very nice set up.

Exactly what I was looking for. Great look and feel. Pretty easy to install too.

Out of all the stocks i've tried this looks and feels the best. Nice and sturdy. I had a problem with feel of other stocks but this one just fits me perfect. And the folding helps with storage.

I purchased this unit after seeing a Tapco folding stock on a friends. Looking at the price I figured that you came out ahead because the Tapco price for the folding stock and hand grip was equal to the cost of this one that also included the pistol grip. From an install perspective it was not hard, but it was not easy. The folding stock went on without much effort as well as the pistol grip. The problem came with the hand grip on the barrel. I had to do some filing and grinding with a drimal tool to get it to fit. The front strap slot also prevent it from fitting together correctly and I had to file that area down as well. Then, when you install the external mount on the lower hand guard you will not be able to insert the cleaning rod. So I removed that and used the blank. Then you find out that when you insert the cleaning rod it hits the base of the barrel preventing it form going completely in. When I examined the wooden hand guard you find that there is a guide hole that prevents the cleaning rod from catching on the barrel. I ended up installing the lower hand guard while the cleaning rod is in place. I just won't ever remove it. Also, as others have reported, unlike the Tapco folding stock, this unit will not fold completely shut if you use the side mount for a red dot site. But, other then that, it's pretty good. If I could go back, I would by the Tapco.

ORDERED ON WED GOT IT ON FRI. IT TOOK ME ABOUT AN HOUR TO PUT IT ON. I LOVE IT LOOKS GREAT FEELS GREAT AND ITS MADE SUPER STRONG, ADJUSTS AND FOLDS FAST AND EASY.

This set went onto my WASR-10 easily. The cheekpiece doesn't seem to want to screw into the stock on one side. The grip is a huge improvement. Note: this stock won't lock in the folded position if you have a side rail installed. Also this setup is significantly heavier than a my friend's WASR-10 with M4 style stock and quad rail mount.

We ordered the quad rail, it was very high quality but in the order ctd included a new catalog. For a few bucks more we got the rail, stock, and grip. Man, does that grip feel good. My son and I spent about 2 great hours installing it. Not only did they swap our order no problem, but they already had a return label in our first order. Could not be happier. There is a bit of a trick to the folder, but with practice it is fast and smooth. Make it 10 bullets. Dirt Rocks!

A little filing involed, a little more work than I thought to install. vary strong poly. I loved the pistol grip, fits my hand like a glove. The fore-hand is great also, you can install all three rails or none, with caps to smooth out the fore-hand. The butt stock is O.K. Like others have said, it's a little long. Now I have to pawn-off my 38" gun case. The stock is about 1" longer than the org. Rom. wasr-10 wood stock. It also will not fold-up right, with the org. side-mount scope rail.

this is an awesome stock! everything worked great on my mak 90. i can even still fire the gun comfortably with the buttstock folded in. the only bad part about the stock is that the bolt that held in my thumbhole part of my old stock was about 1/8 to 1/4 inch too short. so i had to go out another bolt (which is a 6x1.00 mm bolt for u other mak 90 owners) for the pistol grib which cost me another whopping $1.50!!

Ordered this for my WASR-10. Once I got all the wood parts off the WASR this all went on very easily. The folding buttstock is solid,the glass filled nylon is very sturdy. No gunsmithing was required, however I had to file down two "ribs" on the inside of the lower handguard (as suggested in the instructions), but that had no effect on the stability. You need to drill two small "pilot" holes to mount the stock, but anyone with a pencil and a drill can do that. I would recommend this product for anyone wanting to modernize their AK type rifle.

Well first off I started out with good fortune. My father bought one and CTD botched the order and sent two for the price of one. So needless to say I took the other one. Thanks CTD! I put it on my AK 47 and was not impressed. Front hand guard and pistol grip are excellent! The butt stock is a little awkward in the locked out position. It extends out to far because of the adaptor that holds it to the AK. The biggest issue is when it is folded. It takes up so much space it is hard to grab the pistol grip. “Makes it very uncomfortable to shoot it with the stalk folded in”. M4 stalks were not made to be folding stocks. That is why the butt stocks are collapsible.

I ordered these sunday and i was installing them wednesday! They were easy to install, however, my rommie butt stock had to be driven out with a hammer and punch. My ak looks great and the stocks seam sturdy and good quality. 4 bullets because i havent shot it yet. I'll let you know!